This year is going by quite quickly already! There’s only a few months to go until I leave to hike the Great Divide Trail in Canada :).
I’ve been busy with a few things, many mistakes have been made and hopefully you can learn from my losses, haha.
After examining my Hyperlite Mountaingear 4400 Southwest backpack, I’ve thought about various modifications. We can all pick fault in something, so don’t think of this as me saying the backpack isn’t good or something like that. As stated in a few posts now, I’ve been trying to attach a camera bag to my backpack. A camera inside a backpack on a through hike is basically a lead weight–it won’t get used.
A shopping list will be provided at the bottom of the page…
As you can see, I’ve started by sewing something near the shoulder straps at the top. The reason for this is that the webbing on the shoulder straps themselves doesn’t look super durable and I wouldn’t trust it to hold the weight of my camera (Sony a7rII and a 24-70 GM lens, plus the weight of the bag.) This camera combination is already quite heavy and I think you should forget a heavy DSLR with a 24-70mm f/2.8 lens (the extra few hundred grams will make a huge difference and it’s much easier to put a few extra batteries in your backpack i.e. offset the weight somewhere else.) If you have the money, I’d advise getting the 16-35 f/2.8 GM lens instead (assuming you’re okay with that focal length too.) It was out of budget for me and I want to bring a Zeiss Loxia 21mm f/2.8 as well, anyway, I digress…
Instead of cutting long pieces of webbing and then trimming them to size, I tried to make them the right size to begin with and I ended up with barely any material to play with. I’ve never sewn anything before and I feel like a complete idiot really. It was a stupid mistake to make.
The white you see under the webbing is white velcro, and I’m going to change some of that. The loose thread is because I haven’t finished, and if you notice the overlapping webbing on the left is shorter than on the right. I will tidy that up by trimming the excess on the right, but you get the general idea. Like I said… I’m an idiot, haha. I won’t be making that mistake again. In the middle is a carbon fibre rod and then more webbing with a d-ring on the end. Something I’ve found quite useful for preventing fraying and other things is to use a soldering iron. It’ll make the soldering iron messy and obviously a heat gun is better, but it works quite well.
The theory behind this Hyperlite Mountaingear 4400 Southwest backpack modification is that it will pull weight from two points on either side. I can then attach the camera bag to these straps. The extra weight is negligible and it feels pretty comfortable. The two pieces of webbing coming down could be a bit longer or a bit shorter. I wasn’t 100% sure where to put them or how long to make them, all I knew was that if they were the wrong length, I would risk cutting into my neck or shoulders. I think they could possibly be slightly longer… Again, I wouldn’t have had this problem if I made the webbing longer to begin with. I’d have never made this mistake with carbon fibre or metal, so I don’t know why I made this mistake with sewing. I think perhaps because I don’t have much webbing, I was afraid of using too much… Who knows.
At the moment, the carbon fibre rod is loose. One solution is to wrap some cuben fibre tape around it and then sew through the excess tape, another idea is to epoxy one piece of webbing to the carbon fibre. The webbing in the middle has to be able to rotate but equally the carbon fibre rod cannot slide through and fall out, otherwise I’ll be a little unhappy.
Sewing through tape isn’t my favourite thing to do because the glue sticks to the needle. I’ve been using a speedy stitcher sewing awl with a fine needle. The needle has to be bought separately. If you’re from the UK, I’d buy it from eBay.
In the photograph above, you can see the carbon fibre rod is a bit long, I’ll sand the excess later on. It’s certainly not my finest work, but when I finish it, tidy it up and whatnot, it should do the job quite well I think.
I’m going to stick some d-rings near the excess shoulder straps too, as well as one more, on each side, around the hip belt. This will allow room to attach lightweight items or the second points on my camera bag to prevent it from swinging everywhere.
Here is the top of the Hyperlite Mountaingear 4400 Southwest backpack, and as you can see it has a strip of 20mm velcro. In my opinion, this is probably unnecessary most of the time. It does help to get the bag lined up but it’ll probably shred a fleece or whatever. I’m uncomfortable removing it so I’m simply going to cut some extra velcro and leave it there.
- Speedy Stitcher Sewing Awl
- Speedy Stitcher Fine needle
- Bonded Nylon #69 black thread
- 20mm Webbing
- 20mm White Velcro (for backpack)
- 20mm Black Velcro (for webbing)
- 20mm D-rings
I bought my d-rings from eBay. These are 20mm Nexus D-rings.
On a completely unrelated note…
The size 13 bushido remains to be my favourite shoe of all time, but the high arch is painful for me. Bitcoin has dropped in value, and I’ve had duplicate customs charges (one item I received was damaged.) It’s a difficult process getting a refund, and I’ve had a string of bad luck lately. I must say that ZPacks were very helpful in replacing my item.
Some other shoes I have tried… Arcteryx Norvan, Salomon XA Pro and Salomon X ultra 3. The size 13 Salomon XA Pro’s seem to fit quite well.
Photochirp.com is a participant in the Amazon Services LLC Associates Program and eBay affiliate programme; these are affiliate advertising programmes designed to provide a means for sites to earn advertising fees by advertising and linking to amazon.com & eBay.com.